Английская Википедия:Archard equation
Шаблон:Short description Шаблон:Use dmy dates Шаблон:Use list-defined references The Archard wear equation is a simple model used to describe sliding wear and is based on the theory of asperity contact. The Archard equation was developed much later than Шаблон:Interlanguage link (sometimes also known as energy dissipative hypothesis), though both came to the same physical conclusions, that the volume of the removed debris due to wear is proportional to the work done by friction forces. Theodor Reye's model[1][2] became popular in Europe and it is still taught in university courses of applied mechanics.[3] Until recently, Reye's theory of 1860 has, however, been totally ignored in English and American literature[3] where subsequent works by Ragnar Holm[4][5][6] and John Frederick Archard are usually cited.[7] In 1960, Шаблон:Interlanguage link and Mikhail Alekseevich Babichev published a similar model as well.[8] In modern literature, the relation is therefore also known as Reye–Archard–Khrushchov wear law. In 2022, the steady-state Archard wear equation was extended into the running-in regime using the bearing ratio curve representing the initial surface topography.[9]
Equation
- <math>Q = \frac {KWL}H</math>
where:[10]
- Q is the total volume of wear debris produced
- K is a dimensionless constant
- W is the total normal load
- L is the sliding distance
- H is the hardness of the softest contacting surfaces
Note that <math>WL</math> is proportional to the work done by the friction forces as described by Reye's hypothesis.
Also, K is obtained from experimental results and depends on several parameters. Among them are surface quality, chemical affinity between the material of two surfaces, surface hardness process, heat transfer between two surfaces and others.
Derivation
The equation can be derived by first examining the behavior of a single asperity.
The local load <math>\, \delta W </math>, supported by an asperity, assumed to have a circular cross-section with a radius <math>\, a </math>, is:[11]
- <math>\delta W = P \pi {a^2} \,\!</math>
where P is the yield pressure for the asperity, assumed to be deforming plastically. P will be close to the indentation hardness, H, of the asperity.
If the volume of wear debris, <math>\, \delta V </math>, for a particular asperity is a hemisphere sheared off from the asperity, it follows that:
- <math> \delta V = \frac 2 3 \pi a^3 </math>
This fragment is formed by the material having slid a distance 2a
Hence, <math>\, \delta Q </math>, the wear volume of material produced from this asperity per unit distance moved is:
- <math> \delta Q = \frac {\delta V} {2a} = \frac {\pi a^2} 3 \equiv \frac {\delta W} {3P} \approx \frac {\delta W} {3H}</math> making the approximation that <math>\,P \approx H</math>
However, not all asperities will have had material removed when sliding distance 2a. Therefore, the total wear debris produced per unit distance moved, <math>\, Q </math> will be lower than the ratio of W to 3H. This is accounted for by the addition of a dimensionless constant K, which also incorporates the factor 3 above. These operations produce the Archard equation as given above. Archard interpreted K factor as a probability of forming wear debris from asperity encounters.[12] Typically for 'mild' wear, K ≈ 10−8, whereas for 'severe' wear, K ≈ 10−2. Recently,[13] it has been shown that there exists a critical length scale that controls the wear debris formation at the asperity level. This length scale defines a critical junction size, where bigger junctions produce debris, while smaller ones deform plastically.
See also
References
Further reading
- Шаблон:Cite book
- Шаблон:Cite book
- Шаблон:Cite book
- Шаблон:Cite book
- Шаблон:Cite book
- Шаблон:Cite book
- Шаблон:Cite journal
- https://patents.google.com/patent/DE102005060024A1/de (Mentions the term "Reye-Hypothese")
- ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокReye_1860
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокRühlmann_1979
не указан текст - ↑ 3,0 3,1 Ошибка цитирования Неверный тег
<ref>
; для сносокVillaggio_2001
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокHolm_1946
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокHolm_1958
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокHolm_1967
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокPonter_2013
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокKhrushchov_1960
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокVarenberg_2022
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокArchard_1953
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокTLP
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокArchard_1956
не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокAghababaei_2016
не указан текст