Английская Википедия:BMC A-series engine
Шаблон:More citations needed Шаблон:Use dmy dates Шаблон:Use British English Шаблон:Infobox automobile engine The Austin Motor Company A-series is a British small straight-4 automobile engine. Launched in 1951 with the Austin A30, production lasted until 2000 in the Mini. It used a cast-iron block and cylinder head, and a steel crankshaft with three main bearings. The camshaft ran in the cylinder block, driven by a single-row chain for most applications, and with tappets sliding in the block, accessible through pressed steel side covers for most applications, and with overhead valves operated through rockers. The cylinder blocks are not interchangeable between versions intended for conventional end-on mounted gearboxes and the 'in-sump' transaxle used on British Motor Corporation/British Leyland front wheel drive models such as the Mini. The cylinder head for the overhead-valve version of the A-series engine was designed by Harry Weslake – a cylinder head specialist famed for his involvement in SS (Jaguar) engines and several Formula One-title winning engines. Although a "clean sheet" design, the A-series owed much to established Austin engine design practise, resembling in general design (including the Weslake head) and overall appearance a scaled-down version of the 1200cc overhead-valve engine first seen in the Austin A40 Devon which would form the basis of the later B-series engine.
Engine family list
All engines had a cast iron head and block, two valves per cylinder in an OHV configuration and sidedraft SU carburettor. Engines were available in diesel in the BMC tractor.
All A-series engines up until mid-1970 were painted in British Standard (381c) 223 "Middle Bronze Green".[1] This does not include overseas production models such as Australian manufacture. "Factory/dealer warranty replacement" units were painted black, these were primarily distributed for the failures common to the "wet crank" primary gear system in early Minis.
A versions
803
The original A-series engine displaced just Шаблон:Convert and was used in the A30 and Morris Minor. It had an undersquare Шаблон:Convert bore and stroke. This engine was produced from 1952 to 1956.
Applications:
- 1952–56 Austin A30, Шаблон:Convert at 4400 rpm and Шаблон:Convert at 2200 rpm
- 1952–56 Morris Minor Series II, Шаблон:Convert at 4800 rpm and Шаблон:Convert at 2400 rpm
948
1956 saw a displacement increase, to Шаблон:Convert. This was accomplished by increasing the bore to Шаблон:Convert while retaining the original Шаблон:Convert stroke. It was produced until 1964.
Model | Power output | Torque |
---|---|---|
Austin A35 | Шаблон:Convert at 4,750 rpm | Шаблон:Convert at 2,000 rpm |
Morris Minor 1000 | Шаблон:Convert at 4,750 rpm | Шаблон:Convert at 2,500 rpm |
Austin A40 Farina | Шаблон:Convert at 4,750 rpm | Шаблон:Convert at 2,000 rpm |
Austin-Healey Sprite | Шаблон:Convert at 5,200 rpm | Шаблон:Convert at 3,300 rpm |
Austin A40 Farina MkII | Шаблон:Convert at 5,000 rpm | Шаблон:Convert at 2,500 rpm |
Austin-Healey Sprite MkII MG Midget | Шаблон:Convert at 5,500 rpm | Шаблон:Convert at 3,000 rpm |
848
The Шаблон:Convert bore was retained for 1959s Шаблон:Convert Mini version. This displacement was reached by dropping the stroke to Шаблон:Convert. This engine was produced through to 1980 for the Mini, when the 998 A-Plus version supplanted it.
Model | Years | Power output | Torque |
---|---|---|---|
Austin Seven/Austin/Morris MiniШаблон:Efn | 1959–69 | Шаблон:Convert at 5500 rpm | Шаблон:Convert at 2900 rpm |
Riley Elf/Wolseley HornetШаблон:Efn | 1961–62 | ||
Austin A35 Van | 1963–68 | ||
Mini Moke | 1964–68 | ||
Mini 850/City | 1969–80 | Шаблон:Convert at 5300 rpm |
997
The one-off Шаблон:Convert version for the Mini Cooper used a smaller Шаблон:Convert bore and longer Шаблон:Convert stroke. It was produced from 1961 to 1964.
Applications:
- 1961–1964 Austin/Morris Mini Cooper, Шаблон:Convert at 6000 rpm and Шаблон:Convert at 3600 rpm
998
The Mini also got a Шаблон:Convert version. This was similar to the 948 in that it had the same Шаблон:Convert stroke but the bore was increased slightly to Шаблон:Convert. It was produced from 1962 to 1992. This engine was first introduced into the Mk II versions of the Riley Elf and Wolseley Hornet, before becoming common fitment in the mainstream Minis.
Model | Years | Power output | Torque |
---|---|---|---|
Riley Elf/Wolseley Hornet | 1962–69 | Шаблон:Convert at 5250 rpm | Шаблон:Convert at 2700 rpm |
Mini Moke, Australian Mokes. | 1966–82 | ||
Mini Moke, Portuguese Mokes. | 1983–93 | ||
Austin/Morris Mini Cooper | 1964–69 | Шаблон:Convert at 5800 rpm | Шаблон:Convert at 3000 rpm |
Austin/Morris Mini | 1967–80 | Шаблон:Convert at 5250 rpm | Шаблон:Convert at 2700 rpm |
Mini Clubman | 1969–75 | ||
Mini (automatic) | 1969–80 | Шаблон:Convert at 4850 rpm | Шаблон:Convert at 2750 rpm |
1098
The Шаблон:Convert version was fitted to:
- MG Midget Mk1 1098cc from Oct 62- 64
- MG Midget Mk2 1098cc of 1964- 66
- Austin A35 Van 1098cc of 1962- 68
- Austin A40 Farina Mk2 - From Oct 62- 68
- Morris Minor from Oct 62- 71.
- Austin / Morris BMC Saloon from 1962.
- Mini and its derivatives, the 1098cc engine mounted transversely.
It was a stroked (to Шаблон:Convert) version of the 998 previously used in the Riley Elf and Wolseley Hornet. It was produced from 1962 to 1980.
1070
The Шаблон:Convert version was another one-off, this time for the Mini Cooper S. It used a new Шаблон:Convert bore size and the Шаблон:Convert stroke from the 848. It was only produced in 1963–1964. Paired with the even rarer Шаблон:Convert version, below, it became that rarest of things: an oversquare A-series engine.
Applications:
- 1963–1964 Austin/Morris Mini Cooper S, Шаблон:Convert at 6000 rpm and Шаблон:Convert at 4500 rpm
970
The Mini Cooper S next moved on to a Шаблон:Convert version. It had the same Шаблон:Convert bore as the 1071 cc Cooper S but used a shorter Шаблон:Convert stroke. It was produced from 1964 to 1965.
Applications:
- 1964–1967 Austin/Morris Mini Cooper S, Шаблон:Convert at 6,500 rpm and Шаблон:Convert at 3,500 rpm
1275
The largest A-series engine displaced Шаблон:Convert. It used the Шаблон:Convert bore from the Mini Cooper S versions but the Шаблон:Convert stroke from the plain Mini Cooper. It was produced from 1964 until 1980, when it was replaced by an A-Plus version. The bore size was around the maximum possible in the block, with very little separation between the middle cylinders, which often contributed to head gasket failures.
Шаблон:AnchorA-Plus versions
British Leyland was keen to update the old A-series design in the 1970s. However, attempts at replacement, including an aborted early-70s British Leyland 'K engine' (unrelated to the later Rover K series) and an OHC version of the A series, ended in failure. During the development of what was to become the Austin Metro, engineers tested the A series against its more modern rivals and found that it still offered competitive (or even class-leading) fuel economy and torque for its size. While in the 1970s the A series had begun to seem dated against a new generation of high-revving overhead cam engines, by the end of the decade a new emphasis on good economy and high torque outputs at low speeds meant that the A series's inherent design was still well up to market demands.
Given this, and the lack of funds to develop an all-new power unit, it was decided to upgrade the A-series unit at a cost of £30 million. The result was the 'A-Plus' Series of engines. Available in Шаблон:Convert, the A-Plus had stronger engine blocks and cranks, lighter pistons and improved piston rings, Spring loaded tensioner units for the timing chain and other detail changes to increase the service interval of the engine (from Шаблон:Convert). More modern SU Carburettors and revised manifold designs allowed for small improvements in power without any decrease in torque or fuel economy. Many of the improvements learnt from the Cooper-tuned units were also incorporated, with A-Plus engines having a generally higher standard of metallurgy on all units, where previously only the highest-tuned engines were upgraded in this way. This made the A-Plus engines generally longer-lived than the standard A series, which had a life between major rebuilds of around Шаблон:Convert in normal service. Studies were made into upgrading the engine to use five main crankshaft bearings but the standard three-bearing crank had proven reliable even in high states of tune and at high engine speeds, so it was not deemed worth the extra funding.
The new engines received distinctive 'A+' branding on their rocker covers and the blocks and heads were colour-coded for the different capacities: yellow for Шаблон:Convert and red for Шаблон:Convert engines.
998 Plus
The A-Plus version of the Шаблон:Convert motor was produced from 1980 to 1992.
Applications:
Years | Model | Power output | Torque |
---|---|---|---|
1980–82 | Mini 1000/City/HL | Шаблон:Convert at 4750 rpm | Шаблон:Convert at 2000 rpm |
1980–82 | Austin Allegro | Шаблон:Convert at 5250 rpm | Шаблон:Convert at 3000 rpm |
1980–90 | Austin Metro | Шаблон:Convert at 5400 rpm | Шаблон:Convert at 2700 rpm |
1982–88 | Mini HLE/City E/Mayfair | Шаблон:Convert at 5000 rpm | Шаблон:Convert at 2500 rpm |
1981–86 | Austin Metro HLE | Шаблон:Convert | Шаблон:Convert |
1988–92 | Mini City/Mayfair | Шаблон:Convert at 5250 rpm | Шаблон:Convert at 2600 rpm |
1275 Plus
The larger Шаблон:Convert engine was also given the "A-Plus" treatment. This lasted from 1980 to 2000, making it the last of the A-series line.
Years | Model | Power output | Torque |
---|---|---|---|
1980–82 | Austin Allegro | Шаблон:Convert at 5600 rpm | Шаблон:Convert at 3200 rpm |
1980–84 | Morris Ital | Шаблон:Convert at 5300 rpm | Шаблон:Convert at 2950 rpm |
1980–90 | Austin Metro | Шаблон:Convert at 5650 rpm | Шаблон:Convert at 3100 rpm |
1982–89 | MG Metro | Шаблон:Convert at 6000 rpm | Шаблон:Convert at 4000 rpm |
1983–85 | Austin Maestro HLE | Шаблон:Convert at 5500 rpm | Шаблон:Convert at 3500 rpm |
1983–93 | Austin Maestro | Шаблон:Convert at 5800 rpm | Шаблон:Convert at 3500 rpm |
1984–89 | Austin Montego | Шаблон:Convert at 5600 rpm | Шаблон:Convert at 3500 rpm |
1989–90 | Austin Metro GTa | Шаблон:Convert at 6000 rpm | Шаблон:Convert at 4000 rpm |
1990–91 | Mini Cooper | Шаблон:Cvt at 5500 rpm | Шаблон:Cvt at 3900 rpm |
1990–91 | Mini Cooper S | Шаблон:Convert at 6000 rpm | Шаблон:Convert at 3250 rpm |
1991–96 | Mini Cooper 1.3i/Cabriolet | Шаблон:Cvt at 5700 rpm | Шаблон:Convert at 3900 rpm |
1991–96 | Mini Cooper S 1.3i | Шаблон:Convert at 5800 rpm | Шаблон:Convert at 3000 rpm |
1992–96 | Mini Sprite/Mayfair | Шаблон:Convert at 5000 rpm | Шаблон:Convert at 2600 rpm |
1275 Turbo
To allow the MG Metro to compete with larger, more powerful hot hatchbacks a turbocharged version of the Шаблон:Convert A-Plus was developed with the assistance of Lotus Engineering. A Garrett T3 turbocharger was fitted along with a unique SU carburettor with an automatic pressure-regulated fuel system. The engine block, cylinder head, pistons, crankshaft and valves were all modified from the standard A-Plus engines. The turbocharger was fitted with an advanced two-stage boost control system which only allowed full boost to be achieved at engine speeds above 4000 rpm - this was to prevent damage to the sump-mounted four-speed gearbox, the design of which dated back to the early 1950s and could not reliably cope with the high torque output of the Turbo engine at low speeds. The quoted power for the Шаблон:Convert A-Plus Turbo was Шаблон:Convert although in practice the tune could vary from car to car and, because the engine was not intercooled power varied significantly depending on the weather. The MG Metro Turbo was entered in the British Touring Car Championship in 1983 and 1984, with the tuned engines producing in excess of Шаблон:Convert. Turbo versions lasted from 1983 to 1990.
Applications:
- 1983–89 MG Metro Turbo, Шаблон:Convert at 6130 rpm and Шаблон:Convert at 2650 rpm
- 1989–90 Mini ERA Turbo, Шаблон:Convert at 6130 rpm and Шаблон:Convert at 3600 rpm
1275 MPi
A special "twin-port injection" version of the Шаблон:Convert engine was developed by Rover engineer, Mike Theaker. It was the last A-series variant, produced from 1997 to 2000. Few changes were made to ensure the engine complies with Euro 2 (later Euro 3) emission standard, such as adding a 3-way catalytic converter and making it twin-point injection, the engine also receive changes with ignition system by having a wasted spark instead of the distributor. For the Japanese domestic market. the engine maintained the single-point injection version of the engine and the radiator is still on the side due to the space constraint for the air conditioner component.
Applications
- 1997–2000 Rover Mini MPi 1.3i (TPi), Шаблон:Convert at 5500 rpm and Шаблон:Convert at 3000 rpm
JOHN COOPER GARAGES
During the 1990s Mini Cooper revival, John Cooper Garages offered a number of factory-approved "Cooper S" and "Cooper Si" upgrades to the standard Coopers. The conversions came with a full Rover warranty, and could initially be fitted by any franchised Rover dealer.
- S pack (carb) Шаблон:Convert
- 1st Si pack (Spi) Шаблон:Convert
- 2nd Si pack (Spi) Шаблон:Convert
- 3rd Si pack (Spi) Шаблон:Convert
- 1997 Si pack (Mpi) Шаблон:Convert @ 5500rpm
- 1999 Si pack (Mpi) Шаблон:Convert @ 6000rpm[2]
Diesel version
The diesel version appeared in 1962, on the BMC Mini tractor. It was developed with the help of Ricardo Consulting Engineers. It was redesign of existing 948 cc version, new purpose-designed cylinder head, with Lucas CAV fuel injection. This engine has dry liners. The block is almost identical to the petrol engine. The oil pump has been removed from the camshaft and is driven by an extension to what would have been the distributor drive. It uses Ricardo-patented "Comet V" combustion chambers, with a compression ratio of 23.6:1. Produced 15 hp at 2500rpm and Шаблон:Convert torque at 1,750 rpm. A petrol version of this modified engine was 'reverse-engineered' for use in the Mini Tractor whilst retaining parts commonality with the diesel variant, rather than using a standard petrol A-series unit. The diesel A series was also sold as a marine engine under the BMC name alongside the diesel B-series engines. Production ceased in 1969.
South African engines
At the end of 1965, BMC South Africa started a new program, with the aim of using more components manufactured in the country (using less imported components from U.K.). They decided to develop and manufacture their own version of the engine. Two versions were made with 1.1 and 1.3 litres, using the same cylinder block. The block was redesigned, new oil circulation arrangements and redesigned main bearing (bigger dimensions) and stronger/biffers camshafts. Both versions use the same connecting rods, but different crankshaft and pistons. Prototypes versions were made by 1969. Production began in 1971, ending in 1980.
Displacement | Bore | Stroke | Horsepower |
---|---|---|---|
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | Шаблон:Convert |
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | Шаблон:Convert |
Nissan production
The A-series design, along with particularly the B-Series, was licensed by Nissan of Japan. Many changes were made for the initial OHV Nissan C engine and the succeeding E and E-1. An early change was to incorporate a five-bearing crankshaft. The cylinder head was modified by swapping plugs and ports, plugs fitted between pushrods and eight ports eliminated the Siamesed inlet and exhaust ports. Nissan modified the design into the later Nissan A engine that was launched in 1966 with an aluminium head and wedge combustion chambers. It formed the basis for many of their following engines, notably the later OHC Nissan E engine]], was scaled up into the Nissan CA engine which culminated in the DOHC Шаблон:Cvt CA18DET. The basic design was also scaled down into the Nissan MA engine. All these engines show their lineage by the characteristic un-skirted crankcase block of the BMC A-series, but with the A and E having the camshaft moved to the right side allowing greater port areas, and a mounting on the right wall of the crankcase for the oil pump, whereas the BMC A-series had the oil pump at the back end of the left-side camshaft.Шаблон:Cn
OHC version
With the intention of updating the current engine, for use in the new Mini Clubman (ADO20), and current ADO16, Leyland developed an OHC version. It appeared in a prototype version in 1971, with single overhead camshaft. It featured redesigned cylinder block, new aluminium cylinder head and twin SU carburetors. Eleven prototypes units were built, in three different capacities, 970, 1070 and 1275 cc. All engines use the same cylinder bore dimension of 70.6 mm, to reduce the number of engine parts, reducing production costs. It uses a modular approach, making it possible to produce the three versions with the same engine block. The lack of investment and the turmoil and chaos in British Leyland, meant the engine never reached production. In 1975 the plan was abandoned in favour of the "A+" version that reached production in 1980.
Displacement | Bore | Stroke | Horsepower | @rpm | Torque | @rpm |
---|---|---|---|---|---|---|
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | 6750 | Шаблон:Convert | 5250 |
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | 6500 | Шаблон:Convert | 5000 |
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | 6750 | Шаблон:Convert | 4500 |
Twin cylinder A-series
Under the code ADO11, a 474cc twin cylinder with a single H2 SU carburetor based on the 948cc unit was built with the intention to be used in ADO15 (Mini) with an in-sump gearbox.[4] In May 1957, the engine was tested in one Austin A35, alongside a 20 hp 500cc air-cooled later 670cc water-cooled 2-cylinder two-stroke engine developed by Dr Joe Ehrlich of EMC Motorcycles[5] that was tested in one Austin A30 before being used in an experimental Austin A30 based prototype with weight reduced to 584 kg (by way of a special lightweight body in steel that was a couple of gauges lighter than normal with altered panels to keep weight at a minimum) known as the Austin A20 or the "Lightweight Austin 7".[6]
In 2021 retired racing driver and Bugatti specialist Ivan Dutton rebuilt an example of the 4 stroke engine from an original head and cylinder block and documented the work on Youtube. He also has the EMC 2-cylinder two-stroke engine which he plans to return to running condition.
Current use
This engine continues to be improved, it has a very large and wide market, whether in the classic car industry or the racing industry. It has a wide OEM manufacturer support. Almost every part of the engine is still made, whether in original specification or improved versions, pistons, camshafts, crankshafts, cylinder heads. Cylinder heads are available in 8v or 16v, made in aluminium with 5, 7 or 8 ports. Additionally over the past few decades it has not been unusual to see the A-Series stretched beyond 1275cc with capacities ranging from as low as 1293cc up to 1479cc, although it is commonly enlarged to 1380cc while retaining its reliability so long it is serviced regularly and well looked after. [7]
The A series engine is currently used in David Brown Mini Remastered. The engine is totally rebuilt, with new internals to an improved specification. The engine used is based in 1275cc MPi version, with larger capacity versions including the 1330cc Monte Carlo [8] as well as the 1380cc and 1450cc Oselli Edition. [9]
Displacement | Bore | Stroke | Compression ratio |
Carburation | Horsepower | @rpm | Torque | @rpm |
---|---|---|---|---|---|---|---|---|
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | 10.1:1 | MPi | Шаблон:Convert | 4600 | Шаблон:Convert | 3100 |
Шаблон:Convert | Шаблон:Convert | Шаблон:Convert | 10.1:1 | MPi | Шаблон:Convert | - | - | - |
Gallery
See also
Notes
References
Further reading
External links
- ↑ Austin Morris (BL) internal documents archives.
- ↑ Ошибка цитирования Неверный тег
<ref>
; для сносокaronline-a
не указан текст - ↑ 3,0 3,1 Шаблон:Cite book
- ↑ Шаблон:Cite book
- ↑ Шаблон:Cite web
- ↑ Шаблон:Cite book
- ↑ Шаблон:Cite book
- ↑ Шаблон:Cite web
- ↑ Шаблон:Cite web
- Английская Википедия
- Страницы с неработающими файловыми ссылками
- British Leyland engines
- BMC engines
- Gasoline engines by model
- Straight-four engines
- Austin Motor Company
- Страницы, где используется шаблон "Навигационная таблица/Телепорт"
- Страницы с телепортом
- Википедия
- Статья из Википедии
- Статья из Английской Википедии
- Страницы с ошибками в примечаниях