Английская Википедия:Bedford HC
The Bedford HC is a small commercial vehicle that was made by Bedford, beginning in 1938.[1] The vehicle shared its running gear with the H-series Vauxhall 10-4 saloon. Production of civilian vehicles ceased during World War II with the HC van re-entering production for a little while following hostilities. The HC was later joined by the heavier duty Bedford JC, which was itself replaced by the higher-roofed Bedford PC after the war. With the arrival of the much more modern Bedford CA the by now outmoded PC was finally retired.[2]
Previous Bedford vans
In 1932 Bedford produced its first light commercial van, it was marketed on the 12 cwt category and was based on the Vauxhall Cadet passenger car but had a more powerful Chevrolet-derived 6-cylinder engine and a heavier American rear axle (taken from the contemporary Chevrolet Independence) which was added in order to accommodate the larger cargo capacity that the van was designed for. Pickup truck variants were also produced. These vehicles were designated as WS and VYC/BYC. Bedford continued to develop its share of the light transport market, with the introduction of the 8 cwt ASYC and ASXC vans, a close derivative of the Vauxhall Light Six car.[3]
Such vehicles were also produced in Australia and New Zealand where they were marketed alongside Chevrolet and GMC trucks, received various locally-built bodies available for specific markets only such as a roadster or coupe utility.
The AS series of vans continued in production until 1939.
Design
The HC's original engine was a four-cylinder unit of 1203 cc, which was rated at 34.5 hp at the time.[1] In January 1939 a wooden-bodied pickup truck version called the "Utility Wagon" was introduced.[4] Payload was Шаблон:Convert. The HC was Bedford's smallest vehicle at the time and after it was discontinued in the autumn of 1948, Bedford stayed out of the segment until the 1963 introduction of the Bedford HA.[5]
Production was suspended in 1940 as World War II began in earnest. While Bedford began building their heavier trucks in 1945, the lighter HC and JC models had to wait until 1946.[6] Beginning in late 1946 HCs received a 1442 cc version of the engine as seen in the Vauxhall 12-4 and the heavier JC, developing 35 hp.[7] The HC was discontinued in September 1948.[8] While the pickup version was not listed after the war, Bedford did offer the interesting "Utilevan" version. This was a glazed four-seater Estate Wagon version of the van with a folding rear seat.[9] The Utilevan was an officially sanctioned conversion by independent coachbuilder Martin Walter, Ltd., who later built the Bedford Beagle.[10]
From mid-1938, the HC was also assembled in Australia where it was marketed as the Bedford 6cwt Carryall. A panel van with lower roof and rounded front doors was available, as were three different coupé utilities: an open delivery, a wellside delivery, and a flareboard delivery.[11] The engine was unchanged from the British market. The range of bodystyles was later increased to seven, including a roadster utility (a pickup without a roof).[12]
Шаблон:Anchor Bedford JC
The heavier duty JC joined the HC in June 1939. The visual differences between the HC and JC vans are a higher roofline and longer Шаблон:Convert wheelbase. The JC received the 1.4-litre "12HP" engine as used in the Vauxhall 12-4 and post-war HCs. The JC's payload is Шаблон:Convert. The JC was built from 1939 until 1940 and again between 1946 and 1948. As with the HC, there was also a 'Utileva'n variant on offer, a carryall version of the van with two folding rear seats and a maximum capacity of seven people.[9]
From the end of 1939, the 10 hp JC was also built by Holden in Australia, in seven different bodystyles.[12] Variations of the Coupé Utility were the most common model, with panel vans also available. Maximum power of the JC's engine was Шаблон:Convert.[12] The JC's chassis was also used for the six-cylinder Vauxhall Model J 14hp passenger car range. Australian built JCs (and 14s) have split windshields, a detail that continued on the succeeding PC model as the smaller panes were cheaper and easier to replace given Australia's gravel roads.
Шаблон:Anchor Bedford PC
In mid-1948 the JC was updated with a column shifted three-speed transmission and 12-volt electrics, which also meant a name change to Bedford PC.[8] The engine and overall appearance remained as before.
The PC was also assembled by Holden in Australia from parts shipped from England. The bodywork behind the cowl was built in Australia and was very different from British models, with different doors with rounded tops and a much lower roofline.[13] Holden offered four bodystyles of their own design: a plain cowl and chassis (PC 6100), an open Coupé Utility (PC 6106), a Wellside Coupé Utility (PC 6108), and the Panel Van (PC 6104).[10]
References
External links
Шаблон:Bedford vehicles Шаблон:Vauxhall timeline 1945 to 1979
- ↑ 1,0 1,1 Шаблон:Cite web
- ↑ Шаблон:Cite book
- ↑ Шаблон:Cite web
- ↑ Шаблон:Cite magazine
- ↑ "You See Them Everywhere", p. 10
- ↑ "You See Them Everywhere", p. 17
- ↑ Шаблон:Citation
- ↑ 8,0 8,1 "You See Them Everywhere", p. 18
- ↑ 9,0 9,1 For Every Load and Every Road: Bedford, pp. 4-5
- ↑ 10,0 10,1 Шаблон:Cite web
- ↑ Шаблон:Cite journal
- ↑ 12,0 12,1 12,2 Шаблон:Cite journal
- ↑ Шаблон:Cite web
.JPG){kind=link}
.jpg){kind=link}
