Английская Википедия:Allison T56 variants

Материал из Онлайн справочника
Перейти к навигацииПерейти к поиску

Шаблон:Short description

Шаблон:Infobox aircraft engine

Шаблон:Main

The Allison T56 turboprop engine has been developed extensively throughout its production run, the many variants are described by the manufacturer as belonging to four main series groups.

Initial civil variants (Series I) were designed and produced by the Allison Engine Company as the 501-D and powered the Lockheed C-130 Hercules. Later variants (Series II, III, 3,5 and IV) gave increased performance through design refinements.

Further derivatives of the 501-D/T56 were produced as turboshafts for helicopters including a variant with a United States military aircraft engine designation of T701, which was developed for the canceled Boeing Vertol XCH-62 project.

Commercial variants (501-D)

501-D10
The initial civil variant, which was proposed in 1955 with Шаблон:Cvt of power at a brake specific fuel consumption (BSFC) of Шаблон:Cvt, a two-stage gearbox with a reduction ratio of 12.5:1, a 14-stage axial flow compressor with a compression ratio over 9:1, a four-stage turbine, and a Шаблон:Cvt, three-blade Aeroproducts A6341FN-215 propeller.[1]
501-D13
(Series I) Commercial version of the T56-A-1 used on the Lockheed L-188 Electra, but using kerosene as the primary fuel and JP4 as the alternate (instead of JP4 as primary and gasoline as secondary), and with the gearbox reduction ratio increased to 13.54 from 12.5, which lowers the propeller blade tip speed by 8 percent to Шаблон:Cvt for the Шаблон:Cvt Aeroproducts 606 propeller; Шаблон:Cvt power rating at sea level takeoff, 14-stage axial compressor, 6 cannular combustion chambers, and 4-stage turbine; 13,820 rpm shaft and Шаблон:Cvt turbine inlet temperature;[2] certified on September 12, 1957.[3]
501-D13A
(Series I) Similar to the 501-D13 but using a Hamilton Standard propeller; certified on April 15, 1958.[3]
501-D13D
(Series I) Similar to the 501-D13 except for the location of the rear mount and using D.C. generator drive; certified on December 18, 1959;[3] used on the Convair CV-580 passenger aircraft.[4]
501-D13E
(Series I) Similar to the 501-D13 except for the location of the rear mount; certified on December 18, 1959.[3]
501-D13H
(Series I) Similar to the 501-D13D but with water-methanol injection; certified on February 20, 1964;[3] used on the USAF's General Dynamics NC-131H Samaritan.[5] and the Convair CV-580.[4]
501-D15
A Шаблон:Cvt engine under developmentШаблон:When for the Lockheed Electra.Шаблон:Sfn
501-D22
(Series II) Similar to the 501-D13A but with Шаблон:Cvt power rating at sea level takeoff, a shroud turbine, gearbox offset up, and no auto-feathering; certified on October 28, 1964.[3] Used on the Lockheed L-100 Hercules.
501-D22A
(Series III); Similar to the 501-D22 but with Шаблон:Cvt power rating at sea level takeoff and air-cooled first-stage turbine blades, vanes, and stalk blades in all four turbine stages; certified on January 23, 1968.[3]
501-D22C
(Series III) Similar to the 501-D22A but with gearbox offset down, integral mount pads, and water-methanol injection; certified on December 27, 1968;[3] powered the Aero Spacelines Super Guppy.Шаблон:Sfn
501-D22D
A Шаблон:Cvt derivative to power the proposed Lockheed L-400, a twin-engine version of the L-100.[6]
501-D22E
Offered in 1979 as the initial engine for Lockheed's proposed L-100-60 (a stretched derivative of the Lockheed L-100).[7]
501-D22G
(Series III) Similar to the 501-D22C but with Шаблон:Cvt power rating at sea level takeoff, a three-mount system, auto-feathering, and no water-methanol injection; certified on March 23, 1984.[3] Used on the Convair CV-580[4]
501-D36
(Series II) Re-engined powerplant for the Royal Canadian Air Force (RCAF) CC-109 Cosmopolitan in 1966.[8]
501-D39
(Series IV) Offered for the Lockheed L-100 civil aircraft,[9] starting in 1979 for the proposed L-100-60 as the successor engine to the 501-D22E, producing Шаблон:Cvt with Шаблон:Cvt propellers;[7] was the commercial version of the 501-M71.[10]
501-H2
Engine for the proposed Vanguard Model 30 lift fan aircraft that was entered in a 1961 vertical takeoff and landing (VTOL) transport competition; powered two Шаблон:Cvt fans within the wings and two Шаблон:Cvt propellers;[11] used a modified compressor for handling larger air flows.[12]
501-M1
Modified engine with new turbine blades that were hollow and air-cooled; on an experimental engine combining features of the 501-M1 with the 501-H2, ran at Шаблон:Cvt for nearly 2.5 hours at a turbine inlet temperature of Шаблон:Cvt in January 1962 under a program funded by the Air Force and Navy.[12]
501-M7B
Replaces the T56-A-7 on an experimental short takeoff and landing (STOL) version of the Lockheed C-130E (internally designated as the GL298-7) targeted in 1963 for the U.S. Army; power increased by 20% over the T56-A-7 due to lowering of the gear reduction ratio from 13.54 to 12.49, propeller blade changes to take advantage of the higher resulting propeller rotational speed, and a new turbine with air-cooled first and second-stage vanes and first-stage blades, so the turbine inlet temperature can be increased from Шаблон:Cvt for the T56-A-7 to Шаблон:Cvt; a Шаблон:Cvt rate engine that is restricted to Шаблон:Cvt and about Шаблон:Cvt of static thrust on the STOL C-130E, but is capable of Шаблон:Cvt thrust at full power and with a larger, Шаблон:Cvt propeller.[13]
501-M22
Internal designation for the T56-A-18;[14] submitted for FAA certification under a new type certificate.[15]
501-M23
Submitted for FAA certification under an amended type certificate.[15]
501-M24
A demonstrator engine started in 1964[16] that was later used to derive the 501-M62B engine developed for the XCH-62 helicopter.[17]
501-M25
A Шаблон:Cvt four-stage fixed turbine engine similar to the T56-A-15, but with a Шаблон:Cvt increase from the T56-A-15's maximum turbine inlet temperature rating of Шаблон:Cvt, and a variable geometry compressor for the inlet vane and the first five stator vanes; investigated in 1965 to power helicopters with a Шаблон:Cvt maximum takeoff weight (MTOW).[18]
501-M26
A Шаблон:Cvt similar to the 501-M25 but with a free turbine instead of a fixed turbine, and a two-stage gas producer turbine;[18] based on the T56-A-18 engine.[19]
501-M34
A Шаблон:Cvt turboshaft engine targeted for a 60-70 seat commuter helicopter proposal from Lockheed-California in 1966.[20]
501-M56
Engine candidate for the turboprop version of the Air Force A-X close air support aircraft, requiring Шаблон:Cvt of engine power.[21]
501-M62B
An internal designation for the engine that became the Шаблон:Convert T701-AD-700 turboshaft, which weighed Шаблон:Cvt and was intended to power the Boeing Vertol XCH-62 heavy-lift helicopter; 15 engines built, 700 hours of component testing, and almost 2,500 hours of engine development testing completed before the helicopter project's cancellation.[22]
501-M69
Engine proposed for transport-type offensive anti-air (TOAA) aircraft versions of the P-3 Orion (stretched derivative) and C-130 Hercules; rated power of Шаблон:Cvt, equivalent installed thrust-specific fuel consumption at cruise of Шаблон:Cvt.[23]
501-M71
A derivative of the T56-A-14 evaluated by NAVAIR in 1982 to achieve 10% lower fuel consumption, 24% more horsepower, smokeless exhaust, and greater reliability.[24]
501-M71K
(Series IV) A Шаблон:Cvt engine using a larger propeller to power the Lockheed L-100-20 (L382E-44K-20) High Technology Test Bed (HTTB) for short takeoff and landing (STOL) starting in 1989,[25] but was destroyed when the HTTB became airborne during a ground test on February 3, 1993.[26][27]
501-M78
A Шаблон:Cvt demonstrator engine for NASA's Propfan Test Assessment (PTA) program. It had a modified reduction gearbox that reversed the direction of rotation and increased the output speed from 1,020 rpm to 1,698 rpm. The engine was attached to an eight-bladed, Шаблон:Cvt, single-rotation Hamilton Standard SR-7L propeller.[28] Shown as an Шаблон:Cvt engine at the 1983 Dayton Air Show,[29] the 501-M78 was flight-tested on a Gulfstream II aircraft beginning in May 1987.[30] Various flight and ground testing programs were carried out on the engine testbed through June 1989.[31]
501-M80C
Also known as the T406-AD-400, a Шаблон:Cvt turboshaft engine.[32] primarily based on the T56-A-427, but with a free-turbine turboshaft added to the single-spool engine; used on the V-22 Osprey tiltrotor assault transport.[33]
PW–Allison 501-M80E
A Шаблон:Cvt contra-rotating geared propfan engine derived from the 501-M80C/T406 turboshaft engine and intended for use on a 92-seat version of the proposed MPC 75 regional aircraft; developed jointly with Pratt & Whitney.[34]
501-M80R3
A turboprop engine offered as an equal partnership between Allison and Pratt & Whitney to power Lockheed's proposed successor to the P-3 Orion, which was developed for the U.S. Navy's long-range air antisubmarine warfare (ASW) capable aircraft (LRAACA) program.[35]
501-M80R33
A propfan engine studied for the MPC 75[36] that was based on the T406 core and rated at Шаблон:Cvt.[37]

Military variants (T56)

Файл:Allison T56 mobile test unit MCAS Futenma 1982.JPEG
A T56 on a mobile test unit at MCAS Futenma, 1982
T56-A-1
(Series I) A Шаблон:Cvt engine delivering Шаблон:Cvt and Шаблон:Cvt residual jet thrust, which is equal to Шаблон:Cvt; single-shaft 14-stage axial flow compressor, cannular combustion chamber with 6-cylindrical through-flow combustion liners, 4-stage axial flow turbine; 13,800-rpm shaft connected to a 2-stage reduction gear with a 12.5-to-1 ratio, consisting of a 3.125-to-1 spur set followed by a 4.0-to-1 planet set.[38]
T56-A-1A
A Шаблон:Cvt engine used on the Lockheed C-130A Hercules.[39]
T56-A-2
Proposed gas generator engines for the McDonnell XHCH-1 helicopter.
T56-A-3
A Шаблон:Cvt engine that was paired with an Aeroproducts propeller and test flown by the Military Air Transport Service (MATS) on a pair of Convair YC-131C twin-turboprop aircraft between January and December 1955.[40]
T56-A-4
A Шаблон:Cvt engine for the C-131D executive transport/VC-131H VIP transport;[41] also the proposed engines for the McDonnell XHRH-1 helicopter, with propeller drive and gas generator bleed for rotor-tip pressure jets.
T56-A-5
A Шаблон:Cvt turboshaft version for the Piasecki YH-16B Transporter helicopter.
T56-A-6
Gas generator engines for the NC-130B (58-0712) boundary layer control (BLC) demonstrator.[42]
T56-A-7
(Series II) A Шаблон:Cvt engine flight-tested on a U.S. Air Force Allison Boeing B-17 flying testbed aircraft, intended for the Lockheed C-130B;Шаблон:Sfn also used on the C-130E; produces about Шаблон:Cvt of static thrust.[13]
T56-A-7A
(Series II) Lockheed C-130B Hercules Starting May 1959.
T56-A-7B
(Series II) Used on the U.S. Air Force C/HC/NC-130B, MC-130E, and WC-130F;[43] similar to -A-7A.
T56-A-8
(Series II) Entered production in 1959;[24] the original engine on the Grumman E-2C, using the Aeroproducts A6441FN-248 propeller.[44]
T56-A-9
(Series I) Used on the U.S. Air Force C/AC/DC/GC/NC/RC-130A and the C-130D.[43]
T56-A-9D
(Series I) Lockheed C-130A Hercules starting December 1956 and on all Grumman E-2A Hawkeyes from 1960.
T56-A-9E
(Series I) Similar to -A-9D.
T56-A-10W
(Series II) Water injection model that entered production in 1960.[24]
T56-A-10WA
(Series II) Used on the P-3A, EP-3A, and RP-3A.[45]
T56-A-11
Ordered for 12 Royal Australian Air Force C-130s in 1958.[46]
T56-A-13
(Series 3.5) Enhancements that improve SFC by 7.9%, increase maximum engine torque limit operation from Шаблон:Cvt, and increase turbine life; tested on a C-130H testbed aircraft in 2012.[47]
T56-A-14
(Series III) Lockheed P-3/EP-3/WP-3/AP-3/CP-140 Aurora from August 1962; entered production in 1964.[24]
T56-A-14A
(Series 3.5) Fuel efficiency and reliability upgrade, Lockheed WP-3D Orion from May 2015.
T56-A-15
(Series III) Lockheed C-130H Hercules USAF from June 1974.
T56-A-15A
(Series 3.5) Upgrade of the T56-A-15 on the Air Force LC-130H.[48]
Файл:US Navy 081219-N-5142K-048 Bob Maiuvo works alongside Aviation Machinist Mate 2nd Class Tim Triest and Aviation Machinist Mate 2nd Class Marquette Beasley.jpg
Maintenance of a T56-A-16, 2009
T56-A-16
(Series III) Used on the KC-130F, KC-130R, LC-130F, and LC-130R.Шаблон:R
T56-A-16A
(Series 3.5).
T56-A-18
A Шаблон:Cvt, Шаблон:Cvt variant that was designed and first run in 1965;[49] Navy-funded development with air-cooled blades and vanes in the first two stages; 50-hour preliminary flight rating test completed in 1968;[50] turbine inlet temperature of Шаблон:Cvt;[19] introduced major gearbox update after 4,000 hours of back-to-back testing, featuring a double helical first gear stage, a planetary helical gear for the second stage, and fewer parts for the accessory gearing (compared with a first-stage spur gear, second-stage planetary spur gear, and separable clamped components in the accessory gearing for the T56-A-7 gearbox);[51] used an eight-bladed Hamilton Standard variable-camber propeller.[52]
T56-A-20
Proposed in 1968 to be funded within the 1969 fiscal year component improvement program (CIP).[53]
T56-A-100
(Series IV) U.S. Air Force EMDP demonstrator[9]
T56-A-101
(Series IV) Offered for the Lockheed C-130 Hercules.[9]
T56-A-422
Used on U.S. Navy Northrop Grumman E-2C Hawkeye aircraft.[54]
T56-A-423
Used on U.S. Navy Lockheed EC-130G and EC-130Q aircraft.[54]
T56-A-425
(Series III) Replaced the T56-A-8 on the Grumman E-2C, using the Шаблон:Cvt Hamilton 54460-1 propeller;[44] Grumman C-2A Greyhound from June 1974.
T56-A-426
Used on the C-2A, E-2B, and TE-2AШаблон:R
T56-A-427
(Series IV) Northrop Grumman E-2 Hawkeye upgrades from 1972.
T56-A-427A
(Series IV) Used on the Northrop Grumman E-2D Advanced Hawkeye (AHE), which first flew in 2007.[55]

T701

T701-AD-700
An Шаблон:Cvt turboshaft powerplant developed from the 501-M62B and intended for use on the canceled three-engine Boeing Vertol XCH-62 heavy-lift helicopter;[56] air flow of Шаблон:Cvt, pressure ratio of 12.8:1, turbine temperature of Шаблон:Cvt, and power/weight ratio of 6.85:1.[57]

See also

Шаблон:Portal Шаблон:Aircontent

References

Шаблон:Reflist

Bibliography

External links

Шаблон:Allison aeroengines Шаблон:Rolls-Royce plc aeroengines Шаблон:USAF gas turbine engines

  1. Шаблон:Cite magazine
  2. Шаблон:Cite conference
  3. 3,0 3,1 3,2 3,3 3,4 3,5 3,6 3,7 3,8 Шаблон:Cite web
  4. 4,0 4,1 4,2 Шаблон:Cite web
  5. Шаблон:Cite web
  6. Шаблон:Cite book
  7. 7,0 7,1 Шаблон:Cite magazine
  8. Шаблон:Cite book
  9. 9,0 9,1 9,2 Шаблон:Cite conference
  10. Шаблон:Cite journal
  11. Шаблон:Cite conference
  12. 12,0 12,1 Шаблон:Cite newsletter
  13. 13,0 13,1 Шаблон:Cite magazine
  14. Шаблон:Cite book
  15. 15,0 15,1 Шаблон:Cite magazine
  16. Шаблон:Harvnb
  17. Шаблон:Cite conference
  18. 18,0 18,1 Шаблон:Cite report
  19. 19,0 19,1 Шаблон:Cite report
  20. Шаблон:Cite magazine
  21. Шаблон:Cite magazine
  22. Шаблон:Cite book
  23. Шаблон:Cite conference
  24. 24,0 24,1 24,2 24,3 Шаблон:Cite report
  25. Шаблон:Cite press release
  26. Шаблон:Cite report
  27. Шаблон:Cite news
  28. Шаблон:Cite magazine
  29. Шаблон:Cite newsletter
  30. Шаблон:Cite magazine
  31. Шаблон:Cite report
  32. Шаблон:Cite report
  33. Шаблон:Cite magazine
  34. Шаблон:Cite report
  35. Шаблон:Cite magazine
  36. Шаблон:Cite conference
  37. Шаблон:Cite magazine
  38. Шаблон:Cite conference
  39. Шаблон:Cite book
  40. Шаблон:Cite magazine
  41. Шаблон:Cite magazine
  42. Шаблон:Cite book
  43. 43,0 43,1 Шаблон:Cite report
  44. 44,0 44,1 Шаблон:Cite conference
  45. Шаблон:Cite manual
  46. Шаблон:Cite newsletter
  47. Шаблон:Cite news
  48. Шаблон:Cite news
  49. Шаблон:Cite newsletter
  50. Шаблон:Cite book
  51. Шаблон:Cite conference
  52. Шаблон:Cite magazine
  53. Шаблон:Cite report
  54. 54,0 54,1 Шаблон:Cite web
  55. Шаблон:Cite news
  56. Шаблон:Cite magazine
  57. Шаблон:Cite conference