Английская Википедия:Archard equation

Содержание

Текст

Текст

Текст

Текст

Текст

Текст

Текст

Текст

Текст

Шаблон:Short description Шаблон:Use dmy dates Шаблон:Use list-defined references The Archard wear equation is a simple model used to describe sliding wear and is based on the theory of asperity contact. The Archard equation was developed much later than Шаблон:Interlanguage link (sometimes also known as energy dissipative hypothesis), though both came to the same physical conclusions, that the volume of the removed debris due to wear is proportional to the work done by friction forces. Theodor Reye's model became popular in Europe and it is still taught in university courses of applied mechanics. Until recently, Reye's theory of 1860 has, however, been totally ignored in English and American literature where subsequent works by Ragnar Holm and John Frederick Archard are usually cited. In 1960, Шаблон:Interlanguage link and Mikhail Alekseevich Babichev published a similar model as well. In modern literature, the relation is therefore also known as Reye–Archard–Khrushchov wear law. In 2022, the steady-state Archard wear equation was extended into the running-in regime using the bearing ratio curve representing the initial surface topography.

Equation

<math>Q = \frac {KWL}H</math>

where:

Q is the total volume of wear debris produced

K is a dimensionless constant

W is the total normal load

L is the sliding distance

H is the hardness of the softest contacting surfaces

Note that <math>WL</math> is proportional to the work done by the friction forces as described by Reye's hypothesis.

Also, K is obtained from experimental results and depends on several parameters. Among them are surface quality, chemical affinity between the material of two surfaces, surface hardness process, heat transfer between two surfaces and others.

Derivation

The equation can be derived by first examining the behavior of a single asperity.

The local load <math>\, \delta W </math>, supported by an asperity, assumed to have a circular cross-section with a radius <math>\, a </math>, is:

<math>\delta W = P \pi {a^2} \,\!</math>

where P is the yield pressure for the asperity, assumed to be deforming plastically. P will be close to the indentation hardness, H, of the asperity.

If the volume of wear debris, <math>\, \delta V </math>, for a particular asperity is a hemisphere sheared off from the asperity, it follows that:

<math> \delta V = \frac 2 3 \pi a^3 </math>

This fragment is formed by the material having slid a distance 2a

Hence, <math>\, \delta Q </math>, the wear volume of material produced from this asperity per unit distance moved is:

<math> \delta Q = \frac {\delta V} {2a} = \frac {\pi a^2} 3 \equiv \frac {\delta W} {3P} \approx \frac {\delta W} {3H}</math> making the approximation that <math>\,P \approx H</math>

However, not all asperities will have had material removed when sliding distance 2a. Therefore, the total wear debris produced per unit distance moved, <math>\, Q </math> will be lower than the ratio of W to 3H. This is accounted for by the addition of a dimensionless constant K, which also incorporates the factor 3 above. These operations produce the Archard equation as given above. Archard interpreted K factor as a probability of forming wear debris from asperity encounters. Typically for 'mild' wear, K ≈ 10⁻⁸, whereas for 'severe' wear, K ≈ 10⁻². Recently, it has been shown that there exists a critical length scale that controls the wear debris formation at the asperity level. This length scale defines a critical junction size, where bigger junctions produce debris, while smaller ones deform plastically.

See also

• Шаблон:Annotated link

Further reading

• Шаблон:Cite book
• Шаблон:Cite book
• Шаблон:Cite book
• Шаблон:Cite book
• Шаблон:Cite book
• Шаблон:Cite book
• Шаблон:Cite journal
• https://patents.google.com/patent/DE102005060024A1/de (Mentions the term "Reye-Hypothese")