Английская Википедия:Giga Press
Шаблон:Short description Шаблон:Use dmy dates Шаблон:Use British English Шаблон:Infobox machine The Giga Press program is a series of aluminium die casting machines manufactured for Tesla, initially by Idra Group in Italy. Idra presses were the largest high-pressure die casting machines in production as of 2020, with a clamping force of Шаблон:Convert.[1][2] Each machine weighs Шаблон:Convert.[1][2]
Base specification Giga Press machines were included in Idra's catalogue in 2018.[3] Tesla began using a custom Шаблон:Nowrap Giga Press in late-2020 for the production of chassis parts for the Tesla Model Y.[4]
Shots of molten aluminium weighing Шаблон:Convert are injected into the cold-chamber casting mold with a velocity of Шаблон:Convert.[5] The cycle time is ~80‒90 seconds,[1] allowing an initial output rate of 40‒45 completed castings per hour, or ~1,000 castings per day.
Operation
Шаблон:Multiple image Die casting works by forcing molten metal alloy inside a reusable mold, then opening the mold to remove the finished piece after it cools and solidifies. The opened mold is cooled to Шаблон:Convert and cleaned by robots, and fresh molten aluminium is prepared for the next cycle to begin 1‒2 minutes after the first cycle. Each fresh casting is trimmed to approximate size, measured, checked for imperfections, and sent for CNC machining to finished size.[6]
Ingots and off-cuts of aluminium are melted in a natural gas-powered melting oven operating at Шаблон:Convert, until liquid. Slag in the form of aluminium oxide is mechanically removed from the surface, and the rest of the liquid metal is pumped through heated pipes to an enclosed warming oven operating at Шаблон:Convert, heated using Шаблон:Convert of electrical power. To prevent the formation of oxides, a tank blanket of nitrogen gas covers the molten aluminium, which is circulated to maintain an even temperature. Argon gas and a rotary-degasser are used to remove impurities, with a silicon carbide filter removing most other particles larger than Шаблон:Convert.[6]
At the beginning of each casting cycle robots spray Шаблон:Convert of soybean oil in a thin layer inside each half of the mold to allow separation. The mold is closed, and a low vacuum of Шаблон:Convert created by pumping the air out. A precise amount of molten metal is pumped from the holding oven into the casting chamber at Шаблон:Convert, and forced into the mold using a high-speed plunger with an additional Шаблон:Convert of lubricant. The mold is opened, and the raw casting removed at Шаблон:Convert.Шаблон:Cn
A robot reaches in and removes the casting, placing it in a quenching tank to reduce the temperature from Шаблон:Convert. A mechanical trim press cuts the approximate edges, recycling excess aluminium into the melting oven. The remaining useful part of the casting is X-rayed to check its internal structure, trimmed by laser, drilled for fittings, and then computer-measured for precision.[6]
Die structure
Tesla's Model Y rear casting dies have four known visible parts:[7][8]
- two large classic main facing dies, oriented vertically with injection from the bottom of the immobile one.
- two smaller side wedging dies, moving in for injection and out for removal.
The front casting suggests an identical die layout, with a possible fifth wedging die underneath (process) for the front-facing (car) crash rail mount.[9]
Metal alloy
Sandy Munro analysed a Model Y casting in 2021 and reported that the casting aluminium alloy used in the large Tesla chassis parts is primarily an aluminium 89.5%‒silicon 8.5% mix, plus several other trace elements, falling within the categorisation of aluminium Association alloy "AA 386":
| Element | Name | Percentage |
|---|---|---|
| Al | Aluminium | 89.482% |
| Si | Silicon | 8.525% |
| Cu | Copper | 0.790% |
| Mn | Manganese | 0.455% |
| Fe | Iron | 0.277% |
| Mg | Magnesium | 0.075% |
| Zn | Zinc | 0.020% |
| V | Vanadium | 0.015% |
| Ti | Titanium | 0.013% |
| Ni | Nickel | 0.009% |
| Zr | Zirconium | 0.005% |
| Pb | Lead | 0.004% |
| Sb | Antimony | 0.000% |
Components
Vacuum inside the closed mold is achieved using a 4,000-litre tank made by Fondarex in Switzerland.[11]
Molten metal is pumped through heated pipes, and rotary degassing is performed to reduce porosity.[12]
Steps and machinery involved: Шаблон:Citation needed
- StrikoMelter Melting and Holding Furnace (Шаблон:Convert)
- Holding oven (~Шаблон:Convert)
- Giga Press ("DCM"‒Die-casting machine)
- Quench oil tank
- Mechanical trim press
- X-Ray machine (porosity check)
- Laser trim
- Drill and tap (machining)
- Laser scanning (coordinate-measuring machine, Шаблон:Abbr)
- Fastener insertion
- Scrap metal shredder (immediate closed loop recycling of aluminium offcuts)
- Vacuum system
History
Tesla
In 2019 Jerome Guillen indicated that Tesla Automation were working on a "giant, giant, giant machine" to "make full-size cars in the same way that toy cars are made".[13] Шаблон:Quote box
In April 2020, Tesla CEO Elon Musk said that Tesla had purchased the two biggest casting machines in the world to cast the Tesla Model Y rear chassis and crash rails.[14][15] In January 2021, Musk stated that the rear chassis of the Tesla Cybertruck would be produced using a casting machine larger than Шаблон:Convert.[16]Шаблон:Needs verification
As of October 2021, Tesla had five casting machines installed at Giga Shanghai, two machines installed at Tesla Factory in Fremont, two machines installed at Giga Berlin, and two machines going into Giga Texas—plus foundations in preparation for many additional Giga Press machines.Шаблон:Cn
During May/June 2022, Idra were assembling a Шаблон:Convert Giga Press.Шаблон:Where[17] Шаблон:Asof, two 9,000 ton presses were available at GigaTexas to cast Cybertruck rears, while Cybertruck front castings are cast on a 6500-ton press that is shared for casting Model Y frames. Total GigaPresses at Texas were two 9,000 ton plus four of the smaller presses.[18]
FremontШаблон:Anchor
In June 2020, permits for foundations to support the Giga Press at Fremont were issued[f 1][f 2] with Tesla filing permit applications for construction work in preparation for Die-Casting Machine #2 (Шаблон:Abbr) in July 2022.[f 3][f 4] During September 2020 DCM1 started producing trial runs of Model Y castings and DCM2 had been installed.[19]
On 11 March 2021, one of the Fremont presses suffered a fire, caused by molten aluminium igniting hydraulic fluid. No injuries were reported.[20]
Germany
Шаблон:As of plans for Giga Berlin included eight Шаблон:Convert die casting machines.[21][22] (Located at Шаблон:Coord.)
European Model Y cars have front and rear cast chassis sections.[23] The first two European Giga Press machines were planned to be delivered to Giga Berlin by the start of 2021.[11]
Shanghai
By October 2020, three locally-made LK Machinery Impress-Plus DCC6000 machines were undergoing assembly for Model Y production.[24] (Located at Шаблон:Coord.) As of October 2021, five machines were available.[25]
Texas
For Tesla Model Y car production at Giga Texas beginning in 2022, Tesla began to deploy a single-piece front in addition to the existing single-piece rear casting.[26]
During the night of 18/19 January 2021, concrete foundations for three Giga Press machines were poured at the Giga Texas factory location near Austin, Texas.[27][28] (Шаблон:Coord)
On 21 January 2021 the first Giga Press components started to arrive on site.[29][30][31]
Шаблон:As of, all major components of the first Giga Press at the Austin site had been craned into place.[32]
On 15 April 2021, components for a second Giga Press started arriving at Giga Texas.[33]
Glovitech
LK Technology delivered one Impress-Plus DCC 6000 machine for Glovitech of South Korea, installed in the Vân Trung Industrial Zone, Việt Yên, Bắc Giang Province, Vietnam.[34] The machine is used for producing large Faraday cages (radio-frequency enclosures) for 5G mobile base stations.[34] The machine was delivered in December 2020, and produced its first castings in March 2021.[35]
Japan
In June 2023 Toyota announced that it was adopting casting technology for its electric vehicles.[36]
In 2023 Japanese auto parts supplier Ryobi announced plans to cast large electric-vehicle body parts and expects to reduce car body manufacturing costs by 20%.[37]
Volvo
By November 2023, orders had been placed for two 9000-tonnes-force Giga Press machines for a new Volvo electric vehicle factory at Košice, Slovakia.[38]
2.0
In September 2023 Tesla was reported to be considering a single-piece casting for entire underbody of its to-be-announced "small car", an easier task than single-casting their existing, larger models. This required learning how to use larger Giga Press machines, reduce mold design costs, and incorporate hollow subframes. Key innovations include using 3D printing to make cast prototypes with industrial sand.[39]
Making a large metal cast can cost $1.5 million. Typically, multiple iterations and tweaks are required, at great expense.[39]
Binder jet printers build casts out of layers of sand stabilized with a liquid binder at a fraction of the cost of using metal and in a fraction of the time. Hollow elements are created after the cast is made by removing sections of sand added during the casting. Parts cast in sand molds require different aluminium alloys and post-cast processing to meet safety and other requirements. Production casting would continue to use metal casts.[39]
The press would need clamping power of 16,000 tons or more, the largest ever made, although this pressure might prevent the use of sand to make hollows. A different type of press would inject molten alloy more slowly that would allow sand cores and produce higher quality castings, although at a slower pace.[39]
References
Fremont permits
External links
Шаблон:Commons category Шаблон:GeoGroup Шаблон:Refbegin
- ↑ 1,0 1,1 1,2 Ошибка цитирования Неверный тег
<ref>; для сносокol5500cs-20190604не указан текст - ↑ 2,0 2,1 Шаблон:Cite web
- ↑ Ошибка цитирования Неверный тег
<ref>; для сносокferrario-20181011не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокvisnic-20200602не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокamafond-20180201не указан текст - ↑ 6,0 6,1 6,2 Шаблон:Cite report
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ 11,0 11,1 Шаблон:Cite news
- ↑ Шаблон:Cite magazine
- ↑ Ошибка цитирования Неверный тег
<ref>; для сносокshahan-20190623не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокmusk-third-row-20200414не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокmusk-20200813не указан текст - ↑ Шаблон:Cite interview
- ↑ Шаблон:Cite news
- ↑ Шаблон:Cite AV media
- ↑ Ошибка цитирования Неверный тег
<ref>; для сносокalvarez-20200910не указан текст - ↑ Шаблон:Cite web
- ↑ Ошибка цитирования Неверный тег
<ref>; для сносокgf4-20200624-p139не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокreuters-20200908не указан текст - ↑ Ошибка цитирования Неверный тег
<ref>; для сносокteslamag-20200922не указан текст - ↑ Шаблон:Cite press release
- ↑ Шаблон:Cite press release
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite twitter
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite video
- ↑ Шаблон:Cite news
- ↑ 34,0 34,1 Шаблон:Cite news
- ↑ Шаблон:Cite press release
- ↑ Шаблон:Cite web
- ↑ Шаблон:Cite web
- ↑ Шаблон:Cite press release
- ↑ 39,0 39,1 39,2 39,3 Шаблон:Cite news
Ошибка цитирования Для существующих тегов <ref> группы «f» не найдено соответствующего тега <references group="f"/>
